Search Results - Gasser HotRods
GasserHotRods.com is the premier All All Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: 1946Austin

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    485
    Views
    16,926

    Ugh. Sanding on the firewall today, and dust...

    Ugh. Sanding on the firewall today, and dust everywhere. Also pulled the '52 Pontiac steering wheel and figured since I was spreading filler, I'd repair it and sand it also. It's got sun baked rash...
  2. Replies
    978
    Views
    90,566

    Is that anywhere near Garden of the Gods?

    Is that anywhere near Garden of the Gods?
  3. Replies
    978
    Views
    90,566

    Glad your weather is holding up so you can still...

    Glad your weather is holding up so you can still drive the '38!
  4. Replies
    1
    Views
    31

    Yes, I put the same system under my buddy's '37...

    Yes, I put the same system under my buddy's '37 Plymouth coupe recently.

    https://i.imgur.com/aUDPcpql.jpg?1

    They work fine as long as you don't want the front stance too high. The higher you...
  5. Replies
    485
    Views
    16,926

    Thanks! I putter along and seem to get a few...

    Thanks! I putter along and seem to get a few things done most days.
  6. Replies
    7
    Views
    110

    Now you really have to turn in your Ford guy...

    Now you really have to turn in your Ford guy card! :)
  7. Replies
    485
    Views
    16,926

    Hit the all indoor swap meet today, but not much...

    Hit the all indoor swap meet today, but not much I needed or wanted. I found a set of racing harnesses that I'll use just the lap belt out of. A chrome breather for a buck, and 4 flapper discs just...
  8. Thread: Oh man

    by 1946Austin
    Replies
    7
    Views
    130

    If I could get an electronic Hilborn for $2,000...

    If I could get an electronic Hilborn for $2,000 or less I would too. They cost about $2300 for the conversion, if you have the intake. Then you'll spend $500-$700 for a ECU. I've investigated that...
  9. Replies
    7
    Views
    110

    Better turn in your Ford guy card. ;)

    Better turn in your Ford guy card. ;)
  10. Replies
    7
    Views
    110

    I don't think they even had a 351 back at that...

    I don't think they even had a 351 back at that time period when the GT40 was built? That was May of 1964 when it first raced. Later versions did race with SBF engines though.
  11. Thread: Oh man

    by 1946Austin
    Replies
    7
    Views
    130

    Now here's the really hot ticket! A Weiand mid...

    Now here's the really hot ticket! A Weiand mid rise tri power intake with the 3 old school style Holley carbs that were used on those mid 60's Corvette Tripower 427 engines, BUT made to fit a SBC!!
    ...
  12. Replies
    485
    Views
    16,926

    Thanks Mario. I'll need to pull some of this off...

    Thanks Mario. I'll need to pull some of this off when I paint the firewall. I wont color match the firewall to the body, so it will be gloss black. I'll pull the master off and clear coat that, and...
  13. Replies
    485
    Views
    16,926

    The front lines took all the time. The back line...

    The front lines took all the time. The back line was just the bend to the prop valve, and then strapping it to the frame underneath, and a bend at the axle. Pretty fast and simple. I did the...
  14. Replies
    485
    Views
    16,926

    Gary, I bought a Shift Technologies kit that has...

    Gary, I bought a Shift Technologies kit that has the solenoid fittings, and wiring for about $35. It didn't come with the electrical connector so had to buy a new one for $11. This and a toggle...
  15. Replies
    485
    Views
    16,926

    Got all my brake lines bent up, double flared and...

    Got all my brake lines bent up, double flared and terminated. Only forgot one fitting while flaring ends, and it was long enough to trim the flare off and slip a new fitting on before flaring again....
  16. Replies
    485
    Views
    16,926

    I always use plain old Rustoleum black enamel....

    I always use plain old Rustoleum black enamel. And I always brush it or roll most of it. For the crevices and tight spots I use gloss black engine enamel in spray cans. I take the nozzle and spray...
  17. Thread: Really

    by 1946Austin
    Replies
    2
    Views
    55

    It's extremely weird, and I can't imagine anyone...

    It's extremely weird, and I can't imagine anyone paying his price for a car that doesn't run or drive? And as you mentioned Lash that drag link has big time bump steer written all over it! Typical of...
  18. Replies
    117
    Views
    2,840

    Nice work Mario!

    Nice work Mario!
  19. Thread: Oh man

    by 1946Austin
    Replies
    7
    Views
    130

    Checked his sales at the HAMB and he's got...

    Checked his sales at the HAMB and he's got another there with the same "Weber style" carbs on an Edlebrock intake for $1500. It doesn't have the nicely fabricated fuel lines this set has, and it has...
  20. Thread: Oh man

    by 1946Austin
    Replies
    7
    Views
    130

    He had a cool tripower on a tunnel ram for sale...

    He had a cool tripower on a tunnel ram for sale on Ebay for $2250 recently. I wanted it so bad, but couldn't bring myself to paying that much. Then I noticed it was also on the HAMB site for $1750,...
  21. Replies
    485
    Views
    16,926

    After applying the burl wood vinyl to one end of...

    After applying the burl wood vinyl to one end of the dash it became pretty apparent that it was going to be a bit too much. Plus it looked like it might need a chrome trim strip to edge it and look...
  22. Replies
    485
    Views
    16,926

    Had one of those moments last night just as I was...

    Had one of those moments last night just as I was about to hit the sack. Hate when this happens, as it usually means I'll wake up worrying about it. One of the things I also did yesterday was install...
  23. Replies
    485
    Views
    16,926

    Got so caught up in working on the '39 today that...

    Got so caught up in working on the '39 today that I lost track of time. Missed our car club Tuesday night get together at the local pizza parlor. But it was worth it as the day was pretty productive....
  24. Replies
    485
    Views
    16,926

    I realized yesterday that my front axle is...

    I realized yesterday that my front axle is missing the lower shock mounting plate! It bolts to two of the U bolts, and sits below the axle. Of course I also forgot I need to fabricate the upper shock...
  25. Replies
    485
    Views
    16,926

    I bought a kit for mine Gary. It has a solenoid...

    I bought a kit for mine Gary. It has a solenoid and fittings to mount it to the 4th gear port and lock up the converter in 4th when pressure is high enough. It also came with a plug to connect to the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4