Search Results - Gasser HotRods
GasserHotRods.com is the premier All All Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: fiftythreechevy

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    49
    Views
    4,112

    Thanks. It was 200 bucks, thought it was too good...

    Thanks. It was 200 bucks, thought it was too good to pass on. Still has a 4.56 ring gear on it if I decide I want to go that way.
  2. Replies
    49
    Views
    4,112

    Okay, made some progress. Picked up a Detroit...

    Okay, made some progress. Picked up a Detroit Locker for the rear end, too good of a deal to pass up. Also scored an Edelbrock intake for the 460 for 115 bucks. Disassembled the front clip, pulled...
  3. Replies
    10
    Views
    739

    Welcome. I'm gonna get a bag of popcorn once the...

    Welcome. I'm gonna get a bag of popcorn once the pics start coming in. Compressors are expensive for sure. If your looking for a Tig welder, Lincoln makes a square wave new for 1400, if you look you...
  4. Replies
    49
    Views
    4,112

    Okay, picked up the Studebaker wheels today, 4...

    Okay, picked up the Studebaker wheels today, 4 1/2 inches wide should compliment the twelves out back. 103925
  5. Replies
    49
    Views
    4,112

    Vall, no, I am gonna stuff the axle underneath...

    Vall, no, I am gonna stuff the axle underneath the car and work out the pinion angle to set the perches. I have a friend coming this weekend to help with determining that as well as where the springs...
  6. Replies
    1,512
    Views
    125,602

    Well Lash I might just give it a try. Or maybe...

    Well Lash I might just give it a try. Or maybe I'll drive to your side of the state and let you at it! I'm sure I can manage, and maybe learn something along the way. If I do my buddy will want to do...
  7. Replies
    49
    Views
    4,112

    Pulled the pinion and the gears, gonna take it...

    Pulled the pinion and the gears, gonna take it down the sandblast it maybe this weekend. Gotta get new perches and figure out placement, weld them up then time for paint.103921
  8. Replies
    1,512
    Views
    125,602

    Vall, I do like the look of the holes as well!!!...

    Vall, I do like the look of the holes as well!!! I have contemplated them for my build, but my car is heavy and the big block is heavy as well. I might get away with them yet.

    I must say however,...
  9. Replies
    1,241
    Views
    104,492

    Grand Coulee is a neat place. Sounds like you get...

    Grand Coulee is a neat place. Sounds like you get great gas mileage too! Congrats on a successful trip.
  10. Replies
    2
    Views
    258

    That is a cool car. There's a Morris Minor here...

    That is a cool car. There's a Morris Minor here that would make someone a good project close to me, 400 bucks.
  11. Replies
    49
    Views
    4,112

    Woohoo!!! Work finally slowed down enough I got...

    Woohoo!!! Work finally slowed down enough I got the axle all welded up. Didn't penetrate like I wanted the first time, second time is the charm!!! Gave it a wider channel this time and made a couple...
  12. Replies
    1,512
    Views
    125,602

    Looks great Lash. Are you going with the holes or...

    Looks great Lash. Are you going with the holes or no holes on the axle? You're paintjob looks great too. My friend and I are going to try to lace my top once it's ready for paint, will be the first...
  13. Replies
    49
    Views
    4,112

    Went to the pull and save today and found a 4.10...

    Went to the pull and save today and found a 4.10 limited slip for the 8.8. Looks like its in good condition. Hopefully I can get the axle welded back together this weekend and start on the install of...
  14. Replies
    49
    Views
    4,112

    Okay, the axle is almost ready to weld back...

    Okay, the axle is almost ready to weld back together, I will post pics when the welding is done. I did score some old school 15x12 wheels today, I am super excited. 103887
  15. Replies
    49
    Views
    4,112

    Yes. They are smaller combustion chambers and...

    Yes. They are smaller combustion chambers and will work much better than what are on it now.
  16. Replies
    49
    Views
    4,112

    Picked up the motor for her tonight, a 460 out of...

    Picked up the motor for her tonight, a 460 out of a 72 Lincoln. Already have a set of 68 429 heads for it. Getting closer!103863
  17. Replies
    49
    Views
    4,112

    Okay, I fixed the signature. I'm gonna try a...

    Okay, I fixed the signature. I'm gonna try a couple pics just to see if this works better from the laptop. Thanks for the heads up. 103855103857103859103861
  18. Replies
    49
    Views
    4,112

    I have been using my phone. I will switch to the...

    I have been using my phone. I will switch to the computer and see if that helps.
  19. Replies
    49
    Views
    4,112

    Thank you, I'm having fun.

    Thank you, I'm having fun.
  20. Replies
    49
    Views
    4,112

    Made my cuts, no turning back now!!!

    Made my cuts, no turning back now!!!
  21. Replies
    49
    Views
    4,112

    Got the perches off. Started looking for the hole...

    Got the perches off. Started looking for the hole for the door handle, as the last guy welded them shut. I am now covered in bondo.
  22. Replies
    1
    Views
    196

    Top ten car producers

    My uncle shared this, hes an old time hot rudder in Georgia. I thought it was interesting as well. https://para-rigger.posthaven.com/top-ten-car-producing-countries-1950-2019
  23. Replies
    6
    Views
    834

    Cool build for sure. Looks like you're off to a...

    Cool build for sure. Looks like you're off to a great start. The Vette looks great too. I just bought my wife a 78 vette for her birthday this year, she's almost ready for the road. Keep the pics...
  24. Replies
    10
    Views
    806

    Thank you Road Angels and 46 Austin. You guys are...

    Thank you Road Angels and 46 Austin. You guys are a wealth of info. The website was super helpful as well.
  25. Replies
    10
    Views
    806

    Thank you guys for the help, it really is...

    Thank you guys for the help, it really is appreciated. I'm going to pick up the 64 axle at least, the guy only wants 20 bucks for it. The guy with the 55 offered to get it to me in Washington through...
Results 1 to 25 of 49
Page 1 of 2 1 2