Search Results - Gasser HotRods
GasserHotRods.com is the premier All All Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: 1946Austin

Page 1 of 20 1 2 3 4

Search: Search took 0.27 seconds.

  1. Replies
    1,241
    Views
    104,363

    Thanks Lash! I think after nearly 40 years of...

    Thanks Lash! I think after nearly 40 years of drilling holes as an electrician I'll try to muddle through drilling them. I'm going to keep the PCV hole back towards the rear on driver's side to...
  2. Replies
    1,512
    Views
    125,451

    I have a friend who gave me a pair of those gloss...

    I have a friend who gave me a pair of those gloss black powder coated tank brackets. I bought a nice old Eelco tank at a swap meet some years back to put on my Austin, but it didn't look good on that...
  3. Replies
    1,241
    Views
    104,363

    If you read my earlier post I mentioned I have to...

    If you read my earlier post I mentioned I have to drill a hole in each valve cover. One for a PCV valve, and another for a breather, where I'll fill oil also.
    Longer shackles are now 4.25" between...
  4. Replies
    434
    Views
    25,853

    I just went back and did another look see, just...

    I just went back and did another look see, just to find more cool stuff on the Fiat! I noticed the hand brake it's got, instead of a foot operated brake! That had to get interesting if the little car...
  5. Replies
    434
    Views
    25,853

    That's no hose clamp! It's another muffler U bolt...

    That's no hose clamp! It's another muffler U bolt from the same box the rollbar U bolts came from! :)
  6. Replies
    1,241
    Views
    104,363

    I wondered the same Mario. They were new pieces I...

    I wondered the same Mario. They were new pieces I found at a swap meet. Appeared to have never been used, and now I know why! Quick cut with the band saw on one end was all it took. I stopped just...
  7. Replies
    419
    Views
    26,460

    Looks great Mario! Will you make up hard...

    Looks great Mario!
    Will you make up hard panels for the headliner, or buy a headliner pre made?
  8. Replies
    434
    Views
    25,853

    Not sure I could work the shifter in that...

    Not sure I could work the shifter in that location? That's a cool Fiat though!
  9. Replies
    41
    Views
    1,487

    I broke out my insulated Carhardt overalls today!...

    I broke out my insulated Carhardt overalls today! High was low 40's here, and those warm overalls felt pretty comfy working in the unheated shop!
  10. Replies
    1,241
    Views
    104,363

    Beginning to chip away at my winter projects on...

    Beginning to chip away at my winter projects on the '39. I pulled the valve covers off, and test fitted the new Brodix valve covers. Passenger side just cleared the firewall by 1/4"! Driver's side...
  11. Replies
    41
    Views
    1,487

    With all the adjustment your 4 link has, there's...

    With all the adjustment your 4 link has, there's no reason not to proceed with final weld work on it. I will make one suggestion, and that's to mount the panhard bar frame bracket on the bottom side...
  12. Replies
    434
    Views
    25,853

    Link doesn't take me to any Fiat Mario. Just to...

    Link doesn't take me to any Fiat Mario. Just to Marketplace in general.
  13. Replies
    17
    Views
    493

    I agree the balance tube isn't necessary, but it...

    I agree the balance tube isn't necessary, but it does help some, even with progressive linkage. At least when you stomp the throttle and open up both carbs. But probably a waste of money with...
  14. Replies
    11
    Views
    173

    I'm getting one for my driveway! Just to mess...

    I'm getting one for my driveway! Just to mess with anybody who pulls in!
  15. Replies
    18
    Views
    203

    You must mean Mario? I'm far from a guru with...

    You must mean Mario? I'm far from a guru with computers!
  16. Replies
    11
    Views
    173

    Holy crap! That would freak me out every time I...

    Holy crap! That would freak me out every time I looked down at it!
  17. Replies
    3
    Views
    64

    It might be the same, but not sure? I've got a...

    It might be the same, but not sure? I've got a '69 Suburban, and it's been converted to later 5x5" drums, and spindles. Not sure if pre '76 are the same? Of curse if yours does fit, then you've got...
  18. Replies
    1,241
    Views
    104,363

    I agree of course, although I've heard guys...

    I agree of course, although I've heard guys question the mixing of eras. A friend had these and finally decided they were too modern for his tastes. So I jumped on the cheaper price. I still have to...
  19. Replies
    11
    Views
    173

    Just do some faux holes in your coffee cup!

    Just do some faux holes in your coffee cup!
  20. Replies
    2
    Views
    67

    I always wondered what happened to Tom Hanna when...

    I always wondered what happened to Tom Hanna when he took leave of drag racing? And then when he came back with his unbelievable rail in 2002 and I saw the coverage of the build, and how fantastic...
  21. Replies
    1,512
    Views
    125,451

    Looks great, and ties into your theme of lotsa...

    Looks great, and ties into your theme of lotsa holes!
  22. Thread: Front Axles

    by 1946Austin
    Replies
    5
    Views
    79

    I haven't but have a friend who did use one, and...

    I haven't but have a friend who did use one, and I've seen a couple others.
    They are somewhat light tubes, but the assemblies at the spindles are much larger, and heavier than traditional spindles....
  23. Replies
    3
    Views
    64

    I can tell you that the only years Chevy used a...

    I can tell you that the only years Chevy used a 5x5" bolt pattern was in the Chevy trucks from around 1975 to maybe 1986. So if there's a chance to find an 11" x 2" drum that interchanges it would be...
  24. Replies
    18
    Views
    203

    Have to try that trick Steve. None would enlarge...

    Have to try that trick Steve. None would enlarge for me.

    edit-Worked perfectly Steve!
  25. Replies
    1,241
    Views
    104,363

    Got a pair of non period correct valve covers for...

    Got a pair of non period correct valve covers for the '39 Chev. Haven't been happy with the old finned covers, as they're just not that cool. And I found a pair of NOS B&M covers I really wanted, but...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4