Search Results - Gasser HotRods
GasserHotRods.com is the premier All All Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: raj4851

Page 1 of 3 1 2 3

Search: Search took 0.04 seconds.

  1. Replies
    17
    Views
    500

    HI, & thanks for the input. Actually the...

    HI, & thanks for the input. Actually the Edelbrocks work just fine. There tends to be a little bit of a "hotsoak" problem, although I haven't been bothered by it in a while. Those carburetors are...
  2. Replies
    17
    Views
    500

    Hi guys, & thanks for the input. It appears I've...

    Hi guys, & thanks for the input. It appears I've got a lot more research to do, along with experimentation. The Edelbrocks have worked well, but there seems to be more options with the Holleys. ...
  3. Replies
    17
    Views
    500

    Hey Mario, thanks for the thumbs up on my a/f...

    Hey Mario, thanks for the thumbs up on my a/f ratio. I have 500cfm Edelbrocks. Do you run 600 Holleys? If so, stock jetting? It seems we may have had a previous conversation about this. I've...
  4. Replies
    17
    Views
    500

    Hey, Mario, thanks for the post. I'm glad to...

    Hey, Mario, thanks for the post. I'm glad to hear that I seem to have gotten real close to where it ought to be. I had heard the 14.7 ratio & thought I might have a rich problem. Thanks again, Rod
  5. Replies
    17
    Views
    500

    correct air/fuel ratio??

    I just installed a MSD 6al box on my car. I noticed that the a/f ratio was 12.8 at an idle. At 3000rpm it's in the 13 range. Some time ago, it was 14/7 or so, going down the road at 3000rpm. It...
  6. Replies
    2
    Views
    440

    Hi sbauman2, & thanks for the heads-up. I'll...

    Hi sbauman2, & thanks for the heads-up. I'll invest in some of that stuff the next time. I haven't had any trouble with deterioration that I know of but I'll go with the quality stuff nest time. ...
  7. Replies
    2
    Views
    440

    Best stainless steel braided line??

    I did my fuel system in AN6 & AN8 braided s.s.line. It was a hassle & it seemed to "wad up" in the line. I had to make sure there were no pieces that were gouged & sticking out in the way. I...
  8. Replies
    5
    Views
    586

    Thanks guys, yes I had seen an article about...

    Thanks guys, yes I had seen an article about making shorter shifter arms at the trans. It would appear that redrilling the original ones would accomplish the same. Thanks again, Rod
  9. Replies
    5
    Views
    586

    four speed shifters-Hurst or Long??

    I have a Hurst Super Shifter in my car. I had to put a little bit longer stick on it because of location. Regardless, it just seems to have too long of a throw. I drove a '57 Chevy one time & you...
  10. Replies
    1
    Views
    765

    Liberty Performance Components

    I just heard of this company lately. A local machine shop uses the stuff & it looks really nice, cranks, rods, pistons, heads, etc. Anyone heard of or used this stuff? Thanks in advance, Rod
  11. Replies
    19
    Views
    3,674

    Hi Vall, my deck height is about .008 with a...

    Hi Vall, my deck height is about .008 with a quench of about .046 or so. I think I'm right there. Thanks again, Rod
  12. Replies
    19
    Views
    3,674

    Thanks Mario & Vall, I have flattops but my...

    Thanks Mario & Vall, I have flattops but my cranking pressure is about 195-200. I have 62cc chambers. I may be pretty close to 10.5 now. Thanks for all the info, Rod
  13. Replies
    19
    Views
    3,674

    Hey Mario, how did you get 10.5:1, domes pistons?

    Hey Mario, how did you get 10.5:1, domes pistons?
  14. Replies
    19
    Views
    3,674

    Hi guys, & thanks for all the replies. I now...

    Hi guys, & thanks for all the replies. I now have more info to go from. Doc Smith, I've been looking at Trickflo heads, also, maniac, I hear what you're saying about overbuilding a touch. Thanks...
  15. Replies
    19
    Views
    3,674

    Hi Vall, & thanks for the article. The Patriot...

    Hi Vall, & thanks for the article. The Patriot heads are impressive. I understand they are now Promaxx. I'll be looking for a pair of those. Thanks again, Rod
  16. Replies
    19
    Views
    3,674

    sbc aluminum heads

    Hi again, I have another sbc question: what are some viable options concerning sbc aluminum heads? I see Flotec, Patriot(Promaxx), Brodix, Dart, etc. I'm looking for an affordable head that can...
  17. Replies
    8
    Views
    1,537

    Hi guys, & thanks. I am running flat tops & my...

    Hi guys, & thanks. I am running flat tops & my cranking compression is 195-200 lbs. I may be at the ragged edge now. It runs good so maybe I better stand pat. I think I will look into the water...
  18. Replies
    8
    Views
    1,537

    sbc compression

    I'm thinking of upgrading my flat tops to a domes piston, 11:1 or so. Anybody on here had any actual experience with higher compression with today's gas? I'm running 93 octane & a race gas additive...
  19. Replies
    8
    Views
    1,602

    Hi Vall, I'm about ready to do a compression test...

    Hi Vall, I'm about ready to do a compression test & a leak down test. I think I know what I'm going to find. On that presumption, what are the best rings for a sbc? I'm running flattops with 64cc...
  20. Replies
    8
    Views
    1,602

    Hi Vall, I had the intake drilled so I could run...

    Hi Vall, I had the intake drilled so I could run a filler tube w/breather & then drilled my intake for a screw in PCV valve. People do that all the time. A friend of mine just did it & says it...
  21. Replies
    8
    Views
    1,602

    Yes, I made a baffle & fit it under the pcv valve.

    Yes, I made a baffle & fit it under the pcv valve.
  22. Replies
    8
    Views
    1,602

    pcv & oil catch can

    I'm a little bit hesitant to ask, but I'm running a pcv valve & an oil catch can. The car was using oil & evidenced by some oil smoke. I moved the pcv valve to my right valve cover & installed a...
  23. Replies
    7
    Views
    1,862

    Hi guys, and thanks for all the valuable input. ...

    Hi guys, and thanks for all the valuable input. I had read that previously but I wanted to hear what you all had to say. Thanks so much, Rod
  24. Replies
    7
    Views
    1,862

    four corner cooling??

    Hi guys, in looking over the posts, I'm a fairly frequent user. Thanks for all the good advise. It has really helped. By the way, my intake was leaking at the bottom, oil being sucked into the...
  25. Thread: intake leak??

    by raj4851
    Replies
    3
    Views
    810

    Hi guys, and Lash, yes & yes. I'm going to have...

    Hi guys, and Lash, yes & yes. I'm going to have the intake cut the appropriate amount for what I had the block cut. I think that'll fix it. Thanks for the input.
Results 1 to 25 of 59
Page 1 of 3 1 2 3