View Profile: ProMetalShop - Gasser HotRods
GasserHotRods.com is the premier All All Forum on the internet. Registered Users do not see the above ads.
Tab Content
ProMetalShop's Activity
Visitor Messages
About Me
Friends
My Vehicles
More Activity

10 Visitor Messages

  1. View Conversation
    Hi Steve hope all is well ? I did upload some pics of the trunk lid it is pretty rough but I own it could not figure out how to attach them to this message so if you want to look at them in my pics and see what you think I should do to make a repair panel thanks Steve
  2. Enjoy your Vacation, talk to ya when you get back
  3. View Conversation
    Thanks Steve ill send a few pics when I get home from vaca I was thinking relief cuts in the plywood to try to get the proper contour but I'm sure you have a better way thanks again Steve ill get pics sat or sun
  4. Hi Scott
    Glad to see your getting some time in on the coupe ! ! As far as the deck lid, the relief cuts will just get you in more work then you really want, and filling the cuts will cause more damage with the heat and extra material from the filler wire.
    I would like to see a picture of the lid and the area you plan to build the patch panel for.
    There are a few ways to stretch the areas on the panel without cutting. I'm thinking there a few areas that have compound curves, and then an edge that has to turn into the trunk jam. Again send me some pictures and we can get a game plane together.
  5. View Conversation
    Hope all is well I had a question for you re. Making a patch panel for my trunk lid . I can buy one thats 6" tall I believe my damage is taller and thought maybe I would make a plywood jigg . Maybe with some cut relief's to bow it ?? Obviously this will be time consuming but thought it could be fun/ self educating . I have looked at a lot of you posts showing shaping but unsure about the bow ? Am I nuts ? It's not the $250 for the panel just think if its not long enough it's going to just make it more difficult ? I'm on vaca looks like crap out so off to car and gasser planing thanks Steve for you thoughts and guidance
  6. Ya know there are a few ways to tackle that but first let me check on a stash of stuff I have at the shop.... I bought some pick a nut cabinets and had some odd stuff in there from a fellow that worked for the local airport. Some thing tells me I keep running into wing vents that have a square hole in them. They might make a good sacrifice.
  7. View Conversation
    Hey Steve! I need some expert advice to figure out options on my door handle project. I only have one original set of door and crank handles in the Austin, and I want to build a set of 4 ea., but as I mentioned in one post I can't find any steel with square .310" hole for the shaft.
    Any ideas how a guy could maybe form these, build these, or shape them from something? I thought about using small pipe to heat and forge to square, but it might be too weak. Also thought about getting small angle iron and welding together to make a square, but inside corners are rounded. I don't know of any material that comes in this size. I need to make 8 pieces about half inch long, or one piece that I can cut 4" off to make the shafts. After that I can fab up handles and cranks to match and weld to the shafts.
    Thanks,
    Vall
  8. View Conversation
    steve it seems photobucket is down or someithing. can i have your email and i will just send them to you if thats ok.Thanks
  9. View Conversation
    I just made a thread on the "Little Red Wagon" and it appears to be dead...can you help ?...thanks pete
  10. View Conversation
    Pro somthing is messed up I go to Legends and I get Gasser ?????
Showing Visitor Messages 1 to 10 of 10
About ProMetalShop

Basic Information

Date of Birth
February 15, 1955 (64)
About ProMetalShop
Biography:
Hot Rod Sheet Metal Shop Owner
Location:
Danville PA
Interests:
Fabrication and shaping
Occupation:
Hot Rod Sheet Metal Fab & Shaping Shop

Signature


https://www.facebook.com/Prometalshop?ref=bookmarks
ProMetalShop
4431 Snydertown Road
Danville PA.

Statistics


Total Posts
Total Posts
3,068
Posts Per Day
0.94
Visitor Messages
Total Messages
10
Most Recent Message
07-21-2013 08:33 PM
General Information
Last Activity
10-05-2019 12:07 AM
Join Date
12-21-2010
Referrals
0
Home Page
http://prometalshop.com/

23 Friends

  1. 1946Austin 1946Austin is offline

    Administrator

    1946Austin
  2. 19mach69 19mach69 is offline

    Senior Member

    19mach69
  3. 50cruiser 50cruiser is offline

    Junior Member

    50cruiser
  4. 56 VIC 56 VIC is offline

    Senior Member

    56 VIC
  5. Beer:30 Beer:30 is offline

    Senior Member

    Beer:30
  6. blacksheep55 blacksheep55 is offline

    Member

    blacksheep55
  7. casey w casey w is offline

    Senior Member

    casey w
  8. Cptnbob Cptnbob is offline

    Senior Member

    Cptnbob
  9. flyn A flyn A is offline

    Senior Member

    flyn A
  10. gasserman gasserman is offline

    Senior Member

    gasserman
Showing Friends 1 to 10 of 23
Page 1 of 3 123 LastLast